Your position: Home > Raspberry Pi > Display LCDs

Kuman 5" inch Resistive 800x480 HDMI TFT LCD Display Screen Module with Touch Panel Pen SD Card for Raspberry Pi 3 2 Model B RPi 1 B B+ A A+ SC5A

Item Code: SC5A
Price:
USD
$37.98
    Please select the information you wantX
Shipping Cost:
to
Delivery:
Estimated between
Units
  • Description
We are professional factory on making all electronics components based on Arduino and Raspberry Pi. And we also have processional engineer team to offer you tutorials which you can start from beginning. We have all documents( including code) For all kits from Kuman,Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.

Key Features:
● 5 inch resistive touch screen designed for Raspberry Pi 3 2 Model B RPi 1 B B+ A A+, can't work for Raspberry Pi Zero board.
● The Module used SSD1963 LCD controller with 5 inch LCD module with touchpad. Job stability of the module with super anti-jamming capability,far beyond driven solutions on the market SSD1963 , SSD1963 interference poor, black and white with crash risk .
● This LCD has a superior display quality and super wide viewing angle,it using 8080 timing sequence with 16bit parallel bus interface, resolution 800 × 480, 16M colours display panel.
● The LCD has a SD slot, SPI flash footprint. It's pinout is pin to pin compatible with TFT Shield for arduino MEGA 2560.The TFT LCD Module has embedded Font IC, which contain fonts of 10 sizes and 236 icons.With this LCD module, you will be able to draw bigger and nicer fonts, and also extended ASCII characters too.
● For Raspberry Pi user, 5" inch TFT LCD Display Module is compatible with Raspberry Pi 3 2 Model B RPi 1 B B+ A A+ ,Detailed tutorials including project introduction and drives CAN BE PROVIDED FOR FREE,contact us BY Email to get documents

Specifications:
1)5.0" TFT LCD Module, Resolution 800x400, SSD1963 Controller
2)LCD Type: TFT Transmissive Normal White super wide viewing angle
3)LCD Panel: HannStar HSD050IDW1
4)Interface: 8/16bit parallel bus interface
5)PCB Color: Blue
6)On board DC-DC Boost regulator TPS61040 to provide power supply to LCD backlight
7)With SD Cage and Flash IC footprint reserved
8)LCD-specificed intialization code is provided, so that you can save time to optimize power control register and gamma curves for best display performance. We have test the provided code, it gives the best display performanace
9)Module dimension: 133mmx85mmx23mm(including pin header extrusion)
10)Active Area: 108mmx65mm
12)Pixel pitch: 0.135mmx0.135mm
13)Standard 2x20 2.54mm pin header for connection to MCU/development board
14)Module weight: 170grams

Package Contains:
5inch HDMI LCD x 1
HDMI adaptor x 1
Touch pen x 1
USB type A plug to micro B plug cable x 1
RPi screws pack (4pcs) x 1

NOTE:
1.can't work for Raspberry Pi Zero board
2.Power Supply is NOT included.
3.There is a sticker on the LCD screen. Please peel off before use.
Customer Reviews
Recent Reviews
  • ByHaulandCo
  • Jun 01, 2017
I purchased this product at high discount thanl to amzreviewtrader. The order came in on time and was properly packed. The installation with my raspberry pi was a breeze. The screen works great and I'm highly satisfied with the product.
I'm most likely purchase a second one.Awesome..thank you

  • ByPaul Marciniak
  • Jun 01, 2017
he item arrived in excellent packaging. After editing the /boot file, config.txt, it was "plug 'n play." The letters are a little hard to read. I purchased their 3.5" inch monitor, also and, surprisingly the letters were easier to read. All in all, am very satisfied with this product.

It's a very good product sold at an excellent price.

  • ByMike Trethowan
  • Jun 01, 2017
his display works well with my RPI 3. Once the drivers were loaded and the display configuration was ran, after reboot the display functioned as advertised. I like that it leaves some of the GPIO pins exposed. I have not tried to access them, but plan to as soon.

  • ByGraphiccanuk
  • Jan 04, 2017
I am impressed with quality of this screen and works well with the Paspberry Pi 3 B+. It took a while though to get it work, as you need to make some changes in terminal. being a novice it took a bit to work it out, but once I did the screen looks great.

I believe that the display driver package included is for wheezy and not jessie as it would not work properly when I tried it two times. Third time I ended up having to change some code to get it to work for jessie.

For the $60 Canadian I paid though its a great addition to my Raspberry Pi, just don't expect out of the box/plug in ready. You need to have some patience and do some coding to get it to work!