Chinese New Year Holidays Notice

Dear Customers,

Please be informed that our company will be closed from 5th, Feb to 18th, Feb. for Lunar New Year holiday. Our business operation will back to normal on 18th, Feb,2021.

Any orders placed during the holidays will be produced by 19th, Feb,2021

Thank you for your understanding and support. We wish you the very best for the New Year!

Kuman Tech
Your position: Home > Raspberry Pi > Kits

Kuman Raspberry Pi Holder Breadboard Kit, 7 in 1 RAB Holder kit for Arduino Uno R3, Mega 2560 & Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero

Item Code: SC23
    Please select the information you wantX
Shipping Cost:
Estimated Delivery Time:
Please select the country you want to ship from
  • Description
  • This 7 in 1 RAB Holder kit is designed by Kuman for the Raspberry Pi and Arduino hobbyists, the holder is large enough for a Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, Arduino Uno R3 or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard(Arduino rapsberrry pi motherboard and 400 breadboard are not included).
  • Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard.
  • Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W.
  • This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails.
  • Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1kΩ resistors, a screwdriver, and some screws.

This RAB Holder Kit provides you all the necessary components for a simple experiment, including a RPi GPIO Breakout Expansion Board, a Ribbon Cable, Raspberry PI GPIO 40 pin Table Card for wiringPi and BCM codes,a breadboard, quite a lot of jumper wires, an RAB holder, nine LEDs, and ten 1K current-limiting resistors, thus you can start the experiment right away.>
The Kit offer a GPIO hole corresponding table card for you, AS NO ANY PIN MARKED on the Rasberrry Pi motherboard interface, It is not convenient for every experiment to check the Pin corresponding ,Simple Use: Only need to cut along the dotted line down and directly set on the raspberry Pi motherboard , you can intuitive see each pin corresponding GPIO function.>
With this kit, you can fix your Arduino board, Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, and breadboard on the RAB Holder, free of careless short circuits on a metal desk or caused by some metal parts underneath. RPi GPIO Breakout Expansion Board and Ribbon Cable are for the Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W. What’s more, it also comes with 65pcs jumper wires with different length in various colors, therefore, you can just plug them into the control board and breadboard to build circuits, no bothering about complicated soldering.>
RAB Holder Size: 202.7 x 136.5 mm (7.98 x 5.37 inch)

Package Included:
1 x RAB Holder
1 x GPIO 40P Breakout Board For Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W
1 x 20cm FC40 40pin Flat Rainbow Ribbon Cable
1 x GPIO 40 pin Table Card for all Raspberry PI versions 
1 x 830-Point Breadboard
65 x Jumper Wire
10 x 1kΩ Resistor
9 x LED (3 red, 3 yellow, and 3 green)
1 x Screwdriver
4 x M3*6 screws ,4 x PWM2*6 screw, 4 x PWM2*4 screws, 3 x Screw copper nuts
Customer Reviews
Average rating:

Share your thoughts with other customers